旋流分离-颗粒床耦合气固分离装备旋流场静压分布

针对一种集旋风分离器和内置颗粒床优势于一体的新型耦合气固分离装备在无灰负荷及固定床操作条件入口环形空间、分离空间和灰斗内静压场进行研究。结果表明，静压沿周向为非对称分布，轴向为非均匀分布，径向则呈中心低两侧高分布；且存在着静压分布的降压区(0?~180?，以入口处为0?)和增压区(180?~360?)；装备中心的负压及旋流作用在轴向高度H=6.41D(D为旋风壳体内径)以下对静压的影响不再显著；内置颗粒床外壁附近存在“滞留层”，有利于提高装备的分离性能。根据实验数据给出了静压周向分布和静压轴向分布的经验公式。     

Effect of lanthanum doping on water content and diffusion properties of corundum for producing transparent ceramics

The effect of doping corundum with lanthanum on the content of water and other gas impurities, on the diffusion characteristics, on the unit cell size and static strength of fine-crystalline corundum synthesized under thermovapours conditions in a supercritical water fluid was studied.Content, release and diffusion coefficients of water and other volatile impurities in corundum were measured by kinetic thermodesorption mass spectrometry. Water is the main volatile impurity in fine-crystalline corundum. It was found that the introduction of lanthanum into the structure of corundum reduces several times the content of water and other gas-liquid impurities. An increase in the diffusion coefficient of water during the doping of corundum with lanthanum leads to an increase in the degassing rate of fine-crystalline raw materials. When doping corundum, lanthanum, being localized in structural defects, not only displaces structural hydroxyl groups with the formation of strong aluminate-like bonds, but also decreases in the unit cell and increases in the average static strength of the crystals. La-doped corundum, due to the reduced content of water and other gas impurities, is a promising raw material for the production of transparent ceramics.     

Void region restriction for additive manufacturing via a diffusion physics approach

A longstanding challenge in additive manufacturing (AM), the presence of void regions in additively manufactured components, causes two main issues: the enclosing of build material powder in powder bed fusion techniques and limiting tool access in critical post-processing operations to remove sacrificial support structures. As topology optimization has embraced and overcome many of the obstacles of incorporating AM constraints into the underlying numerical optimization statement, there exist few solutions that directly address this fundamental void region issue. By developing computationally efficient and effective solutions to this problem, the integration of these two advanced technologies can be fully realized. Drawing on inspiration from the principles of diffusion physics, a particle diffusion void restriction (PDVR) method is presented in this work that is capable of encouraging the optimization scheme to generate final designs that are fully accessible. Additionally, this method empowers the user to choose the type of post-processing method to clear support material (eg, three-axis or five-axis milling operations, number and orientation of part set-ups) and, therefore, quantify the level of costs associated with the post-processing operation. The PDVR optimization framework is demonstrated on multiple two- and three-dimensional test problems, with physically manufactured examples depicting the real-world benefits this method admits.     

A signal adaptive diffusion filter for video coding: Mathematical framework and complexity reductions

In this paper we combine video compression and modern image processing methods. We construct novel iterative filter methods for prediction signals based on Partial Differential Equation (PDE) based methods. The mathematical framework of the employed diffusion filter class is given and some desirable properties are stated. In particular, two types of diffusion filters are constructed: a uniform diffusion filter using a fixed filter mask and a signal adaptive diffusion filter that incorporates the structures of the underlying prediction signal. The latter has the advantage of not attenuating existing edges while the uniform filter is less complex. The filters are embedded into a software based on HEVC with additional QTBT (Quadtree plus Binary Tree) and MTT (Multi-Type-Tree) block structure. In this setting, several measures to reduce the coding complexity of the tool are introduced, discussed and tested thoroughly. The coding complexity is reduced by up to 70% while maintaining over 80% of the gain. Overall, the diffusion filter method achieves average bitrate savings of 2.27% for Random Access having an average encoder runtime complexity of 119% and 117% decoder runtime complexity. For individual test sequences, results of 7.36% for Random Access are accomplished.     

Investigation of functional core-rim composite part production by inserted powder injection moulding

In this study, the use of Cu and Ni interlayers have been investigated for functional core-rim composite part production with WC-Co 9?wt-% feedstock/steel. For this purpose, different experiments have been performed and joining condition, shear strength and microstructure of the intermediate region have been examined. It has been found that AISI 4340 insert/WC-Co have been joined and 85.8?MPa shear strength achieved, but high speed steel insert has not joined. Moreover, it has been determined that better results are obtained with Ni interlayer. Under the same conditions, when the 40?µm Ni interlayer has been used between AISI 4340 core and WC-Co rim, shear strength has been increased approximately twice and has been 162.7?MPa.     

Measurement of solubility and diffusion coefficients of ethylene in solid and molten low-density polyethylene with different melt indices

The diffusion behavior of ethylene in polyethylene is of great importance for the polymerization and degassing of polyethylene (PE) industry. Based on the gravimetric sorption and desorption measurement approach, an intelligent gravimetric analyzer is applied to obtain the solubility and diffusion coefficients of ethylene in solid low-density PE (LDPE) with different melt indices at 30°C to 70°C, 0 to 4 atm and in molten LDPE at 160°C to 230°C, 0 to 4 atm, respectively. Results indicate that both the solubility and diffusion coefficients of ethylene in solid LDPE are smaller than those in molten LDPE, while the dissolution enthalpy and diffusion activation energy of ethylene in solid LDPE are higher. In addition, one- and two-dimensional diffusion models are built and the effects of particle size, polymer properties, and operation conditions are systematically investigated on the diffusion behaviors of ethylene in solid and molten LDPE.     

Apparent power-law distributions in animal movements can arise from intraspecific interactions

Lévy flights have gained prominence for analysis of animal movement. In a Lévy flight, step-lengths are drawn from a heavy-tailed distribution such as a power law (PL), and a large number of empirical demonstrations have been published. Others, however, have suggested that animal movement is ill fit by PL distributions or contend a state-switching process better explains apparent Lévy flight movement patterns. We used a mix of direct behavioural observations and GPS tracking to understand step-length patterns in females of two related butterflies. We initially found movement in one species (Euphydryas editha taylori) was best fit by a bounded PL, evidence of a Lévy flight, while the other (Euphydryas phaeton) was best fit by an exponential distribution. Subsequent analyses introduced additional candidate models and used behavioural observations to sort steps based on intraspecific interactions (interactions were rare in E. phaeton but common in E. e. taylori). These analyses showed a mixed-exponential is favoured over the bounded PL for E. e. taylori and that when step-lengths were sorted into states based on the influence of harassing conspecific males, both states were best fit by simple exponential distributions. The direct behavioural observations allowed us to infer the underlying behavioural mechanism is a state-switching process driven by intraspecific interactions rather than a Lévy flight.     

Recent progress of the gas diffusion layer in proton exchange membrane fuel cells: Material and structure designs of microporous layer

Proton exchange membrane fuel cells (PEMFCs) have become the most attractive power supply units for stationary and mobile applications. The operation, design characteristics, as well as performance of PEMFCs, are closely related to the multiphase transport of mass, heat, and electricity in the cell, a critical of which is the gas diffusion layer (GDL). It is very important to guarantee the transmission of water and gasses under high current density, and which is the weakness of PEMFCs at present. Microporous layer (MPL) is considered to be the key variable for mass transfer, so varieties of works focus on modification of MPL materials and its structure design. However, there is still a lack of special review to summarize and prospect the progress of MPL in recent years. This review article therefore focuses on the insights and comprehensive understanding of four critical issues of the MPL, the porosity, pore size distribution, wettability, structural design and the durability of MPL. At last, the conclusion and recommendations section summarized the future prospects and recommendations for possible research opportunities.